Mostrar registro simples

dc.contributor.advisorSchaeffer, Liriopt_BR
dc.contributor.authorMozetic, Halston Josépt_BR
dc.date.accessioned2015-01-22T02:15:28Zpt_BR
dc.date.issued2014pt_BR
dc.identifier.urihttp://hdl.handle.net/10183/109171pt_BR
dc.description.abstractO trabalho aborda o desenvolvimento e implantação de um processo de recozimento conjugado com campo magnético induzido. Para este trabalho foi escolhido como material o FeSi, ABNT NM71-2000/ 35F 420M com GNO (Grão-Não-Orientado) devido ao baixo custo de obtenção das peças e também por ser um material de fácil aquisição no mercado. O processo tem como benefício minimizar as perdas magnéticas produzidas pelo corte convencional na borda das chapas elétricas. Para realizar o processo o sistema é composto de um forno, enrolamento de indução e fonte de alimentação. Os parâmetros utilizados no tratamento térmico situam-se na faixa de temperatura de aquecimento até 910ºC e uma indução magnética mínima na faixa de 80 até aproximadamente 1,5 T. Para melhorar as propriedades magnéticas de forma contundente na região deformada buscou-se através do recozimento conjugado com campo induzido um alinhamento dos domínios, ou seja, uma ordenação dos “spins” que juntamente com a elevação de temperatura tenderam a ter um mesmo sentido, facilitando de maneira significativa à passagem do fluxo magnético, propriedade importante para o desempenho dos núcleos das máquinas elétricas. Para avaliar o desempenho do processo, chapas do mesmo material foram cortadas por eletroerosão a fio, onde o perfil do corte permitiu um fluxo magnético uniforme e constante. O efeito do processo de recozimento com indução de campo magnético foi medido conforme determina a norma, ou seja, utilizando o “Quadro de Epstein” para chapas elétricas. Os resultados foram correlacionados com os dados obtidos a partir do uso do ferro-silício, ABNT NM71-2000/35F 420M, com as mesmas condições de uso e testes de laboratório. Do ponto de vista científico, uma das contribuições deste trabalho, está na influência da indução de campo magnético durante o tratamento térmico das amostras, pois é possível verificar um ganho nas propriedades magnéticas apresentadas. Este trabalho permite afirmar que é possível desenvolver e melhorar as propriedades magnéticas em ferro silício com alto desempenho e também sugerir que outras aplicações, onde seja necessário aumento do desempenho magnético, este processo possa ser aplicado.pt_BR
dc.description.abstractThis work presents and discusses the development and application of an annealing process together with the induced magnetic field. For this study development, the chosen material is the iron silicon, ABNT NM71-2000/ 35F 420M, due to the low trading costs and eases of purchase on the market. The process has the benefit of minimizing magnetic losses produced by conventional cutting the edge of the hot plates. To carry out the process system consists of a furnace, induction coil and power supply. The parameters used in the heat treatment are in the range of heating temperature to 910 ° C and a minimum magnetic induction in the range of about 80 to 1.5 T. The challenge of this work was in the fact that structure changes in the silicon iron, allied to inclusions of non-magnetizable materials, modify for worse the performance of magnetic cores. To obtain a structure that the magnetic field could permeate, the silicon iron alloys were selected to eliminate, at most, the presence of non-magnetizable materials, and only then consider a heat treatment process with magnetic induction to make the material suitable for use in cores of electrical machines. To improve the magnetic properties, an alignment of dipoles of the material, through induced magnetic field during annealing was intended. Annealing with induced magnetic field was carried out, observing the performance of the initial magnetic permeability of the samples, and subsequently measured with field saturation equipment. The results were correlated with the obtained data from the use of the FeSi, ABNT NM71-2000/35F 420M, with the same conditions of use and laboratory tests. From the scientific point of view, one of the contributions of this work is the influence of induced magnetic field during the heat treatment of the samples, since it was possible to verify a significant gain in the magnetic properties of the cores electrical machines during the performance tests. As a result of this work, the possibility of using annealing with magnetic induction was presented as a way to increase the permeability of a material with high carbon content, in this particular case, the silicon iron. This work suggests that it is possible to develop and improve the magnetic properties of iron and silicon with high performance also suggest that other applications where necessary increase in magnetic performance, this process can be applied.en
dc.format.mimetypeapplication/pdf
dc.language.isoporpt_BR
dc.rightsOpen Accessen
dc.subjectInduction fielden
dc.subjectLigas de ferro-silíciopt_BR
dc.subjectMagnetics propertiesen
dc.subjectPropriedades magnéticaspt_BR
dc.subjectTratamento térmicopt_BR
dc.subjectAnnealingen
dc.subjectSilicon iron sheetsen
dc.titleMicro estampagem e recozimento conjugado com campo induzido : efeitos no desempenho eletromagnético para chapas elétricas de grão não orientadopt_BR
dc.typeTesept_BR
dc.identifier.nrb000948208pt_BR
dc.degree.grantorUniversidade Federal do Rio Grande do Sulpt_BR
dc.degree.departmentEscola de Engenhariapt_BR
dc.degree.programPrograma de Pós-Graduação em Engenharia de Minas, Metalúrgica e de Materiaispt_BR
dc.degree.localPorto Alegre, BR-RSpt_BR
dc.degree.date2014pt_BR
dc.degree.leveldoutoradopt_BR


Thumbnail
   

Este item está licenciado na Creative Commons License

Mostrar registro simples