Mostrar registro simples

dc.contributor.advisorMaltez, Rogerio Luizpt_BR
dc.contributor.authorReis, Roberto Moreno Souza dospt_BR
dc.date.accessioned2009-06-16T04:13:06Zpt_BR
dc.date.issued2009pt_BR
dc.identifier.urihttp://hdl.handle.net/10183/16135pt_BR
dc.description.abstractSiC é um semicondutor promissor para dispositivos eletrônicos de alta-potência, alta-freqüência e alta temperatura e a síntese de uma camada epitaxial de SiC por implantação, na superfície do Si, pode ser uma via de integração com a tecnologia de Si. Implantação em alta temperatura (600°C) através de uma capa de SiO2, recozimento pós-implantação a 1250°C sob um ambiente de Ar (com 1% de O2) e ataque químico são a base da presente síntese. Implantações à energia de 40 keV foram executadas em substratos SIMOX(111) e Si(111), cobertos com uma capa de 100 nm de SiO2. Implantação em SIMOX foi o foco principal. Isto nos permitiu obter uma camada sintetizada de SiC separada do Si bulk e analisar as conseqüências estruturais. Neste caso, foi produzida a conversão da camada superior de 65 nm de Si superior da estrutura SIMOX em 30-45 nm de SiC. Implantações seqüenciais de C (passos de fluências de ~ 5 × 1016 C/cm2), seguidas por recozimento à 1250°C, permitiu estimar as fluências mínimas de C para atingir a estequiometria como 2,3 × 1017 C/cm2 e 2,8 × 1017 C/cm2, quando implantado em SIMOX e em Si, respectivamente. Espectrometria de Retroespalhamento de Rutherford (RBS) foi empregada para medir a evolução composicional da camada. Pela análise das implantações seqüenciais, foi possível compreender a redistribuição de carbono durante a implantação e recozimento. Uma estrutura de duas camadas é observada no SiC sintetizado separado do Si bulk, sendo a camada superficial mais rica em Si. Microscopia Eletrônica de Transmissão (TEM) mostrou que as camadas sintetizadas são sempre cúbicas e epitaxiais à estrutura original do Si. TEM também mostrou que as implantações diretas, até as fluências mínimas, resultam em uma melhor qualidade estrutural. Para uma fluência muito mais alta (4 × 1017 C/cm2), uma camada completamente estequiométrica é obtida, com redução na qualidade estrutural. Nossos resultados indicam que o excesso de carbono é o principal fator determinante da qualidade cristalina final do SiC sintetizado por feixe de íons, quando comparado ao stress, resultante de um casamento de redes forçado entre o substrato Si e o SiC sintetizado.pt_BR
dc.description.abstractSiC is a promising semiconductor for high-power, high-frequency and hightemperature electronic devices and the synthesis of an epitaxial layer of SiC by implantation, on the surface of Si, can be a route for integration with the Si technology. High temperature implantation (600oC) through a SiO2 cap, 1250oC post-implantation annealing under Ar ambient (with 1% of O2), and chemical etching are the base for the present synthesis. 40 keV carbon implantations were performed into SIMOX(111) and Si(111) substrates covered with a 100 nm SiO2 cap. Implantation into SIMOX was the main focus. It has allowed us to obtain a SiC synthesized layer separated from the bulk silicon and to analyze the structural consequences. In this case, it was performed the conversion of a 65 nm Si(111) overlayer of a SIMOX(111) into 30-45 nm SiC. Sequential C implantations (fluence steps of about 5 × 1016 C/cm2), followed by 1250oC annealing, has allowed to estimate the minimum C fluences to reach the stoichiometric composition as 2.3 × 1017 C/cm2 and 2.8 × 1017 C/cm2, when implanting into SIMOX and into Si, respectively. Rutherford Backscattering Spectrometry (RBS) was employed to measure layer composition evolution. By analyzing the sequential implantations it was possible to understand the carbon redistribution during implantation and annealing. A two-sublayers structure is observed in the synthesized SiC separated from the bulk Si, being the superficial one richer in Si. Transmission Electron Microscopy (TEM) has shown that the synthesized layers are always cubic and epitaxial to the original Si structure. TEM also show that single-step implantations, up to the minimum fluences, result in better structural quality. For a much higher C fluence (4 × 1017 C/cm2), a whole stoichiometric layer is obtained, with reduction of structural quality. Our results indicate that excess of carbon content is the major detrimental factor to determine the final crystalline quality in SiC ion beam synthesis, as compared to the stress, resulting from a forced lattice matching between the Si substrate and the synthesized SiC.en
dc.format.mimetypeapplication/pdf
dc.language.isoporpt_BR
dc.rightsOpen Accessen
dc.subjectFísica da matéria condensadapt_BR
dc.subjectImplantacao ionicapt_BR
dc.subjectSemicondutorespt_BR
dc.subjectCarbeto de silíciopt_BR
dc.subjectSIMOXpt_BR
dc.subjectRetroespalhamento rutherfordpt_BR
dc.subjectMicroscopia eletrônica de transmissãopt_BR
dc.titleSíntese de SiC por implantação iônica de carbono em SIMOX(111) e Si(111)pt_BR
dc.typeDissertaçãopt_BR
dc.identifier.nrb000697370pt_BR
dc.degree.grantorUniversidade Federal do Rio Grande do Sulpt_BR
dc.degree.departmentInstituto de Físicapt_BR
dc.degree.programPrograma de Pós-Graduação em Físicapt_BR
dc.degree.localPorto Alegre, BR-RSpt_BR
dc.degree.date2009pt_BR
dc.degree.levelmestradopt_BR


Thumbnail
   

Este item está licenciado na Creative Commons License

Mostrar registro simples